How to sew a patch pocket

     A patch pocket is a pocket that is sewn on a garment like a patch except that one side is finished and left open.To began fold the top edge down 1/4 inch. Iron or crease with your finger. Make another fold about one inch and pin down. Sew across the edge of the fold. Next fold and crease the sides and bottom of the pocket about 1/2 inch. Then pin the pocket on the center of the right or left side of the shirt, about 6 to 8 inches from the shoulder seam. Last sew it down starting from the right side of the pocket with a zigzag stitch. Go back and forth in one spot about three times.Then sew using a straight stitch all the way around the pocket and end with another three zigzag stitches.

Want to learn more about sewing go to : http://www.faysoriginalsewing.com  Today!

How to sew pants video

 

How to cut out basic pants.

Did you save your measurements?  I hope so because today I am going to write about how to use them to cut out some pants. To begin get some fabric that is 45'' wide and is folded in half  length wise.Also you will need some chalk, a tape measure and some scissors.  Fold the fabric again width wise to desired length of your pants. Add  4 to 6 inches to your waist measurements. This will also include seam allowance.Use your measurement plus 6'' to draw a strait line from the fold of the fabric to toward the salvage to your waist measurements.
Then using your crouch measurements plus 2 1/2'' for the waist casing draw a line down then curve out about 4'' to form a crouch for the pants. Then draw a slanted line from the crouch to the the bottom of the pants slanting out about 1'' for the hem. Lastly cut through all thickness remember to always slide the scissors and not lift them while cutting. See fig. 1. finally look at my picture to see how to sew a pair of simple pants. And always have Fun!

How to measure for pants.

I talked about how to sew pants. So today I am going to write about how to measure a person for pants. To begin get a tape measure. Then measure around the waist. Next measure from the to waist the ankle or  to what ever length you want. Finally measure the crouch which is from the waist line in the front to between the legs to the waist line in the back then sit while holding the tape measure in place.And that's it. Jot down your measurements because you will need them when cutting out the pants.

Last step, How to make pants #5

Finish up the pants by folding the legs up twice to the marks you made during your fitting. Press in the hem and pin. If you don't have access to the person, then get your original pants back out, match up the crotches, and use the leg on the old pants as a guide. Sew the hems close to the fold and press when you're done.That's it! You've made pajama pants. And you didn't spend a fortune on them. Enjoy!
------------------------
http://www.instructables.com

How to sew pants continued #4

 

  Now it is a good time to have a fitting. You want to make sure the rise of the pants will be comfortable. The rise is the distance from the crotch to the waist. Too short and the pants will ride too low..  Get the person inside the pants (if you can) so you have an idea of how much you'll need to fold down the waist to get a comfortable rise. If you don't have the actual person, use the pants you used to make the pattern as a guide. Mark the hems on the legs after you've marked the rise.

Fold down the top of the fabric about 1 / 2 inch and press. Then fold it down again about 1 inch and press. This will hide the raw edge of the fabric inside and form the tunnel for the elastic waist. Pin all the way around the waist but leave an opening about 3 long and mark it with pins so that we'll have a place to thread the elastic in. Sew around the waist close to the fold of the fabric, stopping when you get to the place where you marked the opening.
    

Cut a piece of 1 / 2 inch elastic long enough to fit around the waist of the person plus another three or four inches. Mark the actual waist measurement on the elastic with a sharpie so you will know where to sew when you're ready. Hook one end of the elastic to a big safety pin and thread it through the waistband taking care not to twist it as you go around. Bunch the pants up once you get both ends out, overlap the elastic to the sharpie mark and sew the elastic together using a wide zig-zag stitch for security. Trim off the extra elastic and let the elastic go back up into the waistband. Then sew across the opening to secure it all inside.Fold down the top of the fabric about 1 / 2 inch and press. Then fold it down again about 1 inch and press. This will hide the raw edge of the fabric inside and form the tunnel for the elastic waist. Pin all the way around the waist but leave an opening about 3 long and mark it with pins so that we'll have a place to thread the elastic in. Sew around the waist close to the fold of the fabric, stopping when you get to the place where you marked the opening.

Cut a piece of 1 / 2 inch elastic long enough to fit around the waist of the person plus another three or four inches. Mark the actual waist measurement on the elastic with a sharpie so you will know where to sew when you're ready. Hook one end of the elastic to a big safety pin and thread it through the waistband taking care not to twist it as you go around. Bunch the pants up once you get both ends out, overlap the elastic to the sharpie mark and sew the elastic together using a wide zig- zag stitch for security. Trim off the extra elastic and let the elastic go back up into the waistband. Then sew across the opening to secure it all inside.

--------------------------------
http://www.instructables.com

 

How to make pants continued #3

Fold the leg pieces right sides together. Pin along the inside of the leg pieces from ankle to crotch and sew using a 3/8 inch seam allowance. Because I have boys who like to play in their lounge pants rather than lounge in them, I always reinforce the crotch seam by sewing a second seam just outside the first one. There are fancier ways to reinforce the seams but these are lounge pants, not tuxedo pants. I trim off any excess seam allowance and that seems to work just fine. I've made probably twenty pairs of these for my kids and they never complain about the seam allowance bothering  them.

If your fabric is really prone to fraying, zigzag the raw edges of the legs from ankle to crotch before you pin them together. Then fold the leg piece right sides together and sew a seam up the side from ankle to crotch. Do the same for the other leg. Press the seams open.Turn one leg right side out and slip it inside the other leg. Match up the side seams that you just sewed and pin from there up both sides of the crotch to the waist. Sew along the crotch, pulling the pins as you sew. I reinforce this seam the same way I did the leg seams by sewing a second seam very close to the first one. Then I clip the curve to leave less fabric in the crotch area. Take the pant leg out of the other one but leave the PJ pants inside out.

Now they should look like inside-out pajama pants with raw edges at the waist and legs. If they don't, you are doing it wrong. 

----------------------------

http://www.instructables.com